dumpspedia logo
Drag and drop the DHCP messages from the left onto the correct uses on the right.
Refer to the exhibit.
An engineer configures a static route on a router, but when the engineer checks the route
to the destination, a different next hop is chosen. What is the reason for this?
Refer to the exhibit.
Redistribution is enabled between the routing protocols, and nowPC2 PC3, and PC4 cannot reach PC1. What are the two solutions to fix the problem? (Choose two.)
An engineer is configuring a network and needs packets to be forwarded to an interface for any destination address that is not in the routing table. What should be configured to accomplish this task?
Refer to the exhibit.
Which interface configuration must be configured on the spoke A router to enable a dynamic DMVPN tunnel with the spoke B router?
Refer to the following output:
Router#show ip nhrp detail
10.1.1.2/8 via 10.2.1.2, Tunnel1 created 00:00:12, expire 01:59:47
TypE. dynamic, Flags: authoritative unique nat registered used
NBMA address: 10.12.1.2
What does the authoritative flag mean in regards to the NHRP information?
Refer to the exhibit.
An engineer is trying to generate a summary route in OSPF for network 10.0.0.0/8, but the
summary route does not show up in the routing table. Why is the summary route missing?
Refer to the exhibit.
Which routes from OSPF process 5 are redistributed into EIGRP?
A network engineer needs to verify IP SLA operations on an interface that shows on indication of
excessive traffic.
Which command should the engineer use to complete this action?
Drag and drop the SNMP attributes in Cisco IOS devices from the left onto the correct SNMPv2c or SNMPV3 categories on the right.
Refer to the following output:
Router#show ip nhrp detail
10.1.1.2/8 via 10.2.1.2, Tunnel1 created 00:00:12, expire 01:59:47
TypE. dynamic, Flags: authoritative unique nat registered used
NBMA address: 10.12.1.2
What does the authoritative flag mean in regards to the NHRP information?
Refer to the exhibit.
Why is the remote NetFlow server failing to receive the NetFlow data?
Drag and Drop the IPv6 First-Hop Security features from the left onto the definitions on the right.
A network engineer is investigating a flapping (up/down) interface issue on a core switch that is synchronized to an NTP server. Log output currently does not show the time of the flap. Which command allows the logging on the switch to show the time of the flap according to the clock on the device?
Refer to the exhibit.
An administrator that is connected to the console does not see debug messages when
remote users log in. Which action ensures that debug messages are displayed for remote logins?
An engineer configured the wrong default gateway for the Cisco DNA Center enterprise interface during the install. Which command must the engineer run to correct the configuration?
Which command displays the IP routing table information that is associated with VRF-Lite?
Drag and drop the OSPF adjacency states from the left onto the correct descriptions on the right.
Drag and drop the operations from the left onto the locations where the operations are performed on the right.
Refer to the exhibit.
Network operations cannot read or write any configuration on the device with this configuration from the operations subnet. Which two configurations fix the issue? (Choose two.)
Refer to the exhibit.
An engineer is trying to connect to a device with SSH but cannot connect. The engineer connects by using the console and finds the displayed output when troubleshooting. Which command must be used in configuration mode to enable SSH on the device?
Which command allows traffic to load-balance in an MPLS Layer 3 VPN configuration?
An engineer configured a leak-map command to summarize EIGRP routes and advertise specifically loopback 0 with an IP of 10.1.1.1.255.255.255.252 along with the summary route. After finishing configuration, the customer complained not receiving summary route with specific loopback address. Which two configurations will fix it? (Choose two.)
Refer to the exhibit.
An engineer has configured DMVPN on a spoke router. What is the WAN IP address of another spoke router within the DMVPN network?
Refer to the exhibit.
Which interface configuration must be configured on the spoke A router to enable a dynamic DMVPN tunnel with the spoke B router?
Drag and drop the MPLS terms from the left onto the correct definitions on the right.
Refer to the exhibit.
In which circumstance does the BGP neighbor remain in the idle condition?
Refer to the exhibit.
The ACL is placed on the inbound Gigabit 0/1 interface of the router. Host
192.168.10.10cannot SSH to host 192.168.100.10 even though the flow is permitted. Which action
resolves the issue without opening full access to this router?
Refer to the exhibit.
ISP 1 and ISP 2 directly connect to the Internet. A customer is tracking both ISP links to
achieve redundancy and cannot see the Cisco IOS IP SLA tracking output on the router console. Which command is missing from the IP SLA configuration?
Which configuration adds an IPv4 interface to an OSPFv3 process in OSPFv3 address family configuration?
Refer to the exhibit.
An administrator noticed that after a change was made on R1, the timestamps on the system logs did not match the clock. What is the reason for this error?
Refer to the exhibit.
R1 and R2 are configured for EIGRP peering using authentication and the neighbors failed to come up. Which action resolves the issue?
Refer to the exhibit.
Which configuration denies Telnet traffic to router 2 from 198A:0:200C::1/64?
A)
B)
C)
D)
While working with software images, an engineer observes that Cisco DNA Center cannot upload its software image directly from the device. Why is the image not uploading?
Which attribute eliminates LFAs that belong to protected paths in situations where links in a network are connected through a common fiber?
During the maintenance window an administrator accidentally deleted the Telnet-related
configuration that permits a Telnet connection from the inside network (Eth0/0) to the outside of the networking between Friday – Sunday night hours only. Which configuration resolves the issue?
A)
B)
C)
D)
Refer to the exhibit. an engineer is trying to get 192.168.32.100 forwarded through 10.1.1.1, but it was forwarded through 10.1.1.2. What action forwards the packets through 10.1.1.1?
Refer to the exhibit.
Which configuration configures a policy on R1 to forward any traffic that is sourced from
the 192.168.130.0/24 network to R2?
Refer to the exhibit.
Users in the branch network of 2001:db8:0:4::/64 report that they cannot access the Internet. Which command is issued in IPv6 router EIGRP 100 configuration mode to solve this issue?
Refer to the exhibit.
An engineer is trying to configure local authentication on the console line, but the device is trying to authenticate using TACACS+. Which action produces the desired configuration?
Refer to the exhibit.
Users in the branch network of 2001:db8:0:4::/64 report that they cannot access the Internet. Which command is issued in IPv6 router EIGRP 100 configuration mode to solve this issue?
Refer to the exhibit.
Drag and drop the credentials from the left onto the remote login information on the right to resolve a failed login attempt to vtys. Not all credentials are uf SLA by defining frequency and schedulingsed
A network administrator cannot connect to a device via SSH. The line vty configuration is as follows:
Which action resolves this issue?
An engineer must override the normal routing behavior of a router for Telnet traffic that is destined to 10.10.10.10 from 10.10.1.0/24 via a next hop of 10.4.4.4. which is directly connected to the router that is connected to the 10.1.1.0/24 subnet Which configuration reroutes traffic according to this requirement?
Refer to the exhibit. Site1 must perform unequal cost load balancing toward the segments behind Site2 and Site3. Some of the routes are getting load balanced but others are not. Which configuration allows Site1 to load balance toward all the LAN segments of the remote routers?
Refer to the exhibit.
Users in VLAN46 cannot get the IP from the DHCP server. Assume that all the parameters are configured properly in VLAN 10 and on the DHCP server Which command on interlace VLAN46 allows users to receive IP from the DHCP server?
R1 and R2 are configured as eBGP neighbor , R1 is in AS100 and R2 is in AS200. R2 is advertising these networks to R1:
The network administrator on R1 must improve convergence by blocking all subnets of 172-16.0.0/16 major network with a mask lower than 23 from coming in, Which set of configurations accomplishes the task on R1?
Drag and drop the packet types from the left onto the correct descriptions on the right.
Refer to the exhibit.
In which circumstance does the BGP neighbor remain in the idle condition?
Refer to the exhibit.
The network operation team observes a traffic forwarding issue between R2 and R3:
Ping and traceroute of loopback IP address from R2 to R3 is successful.
iBGP peering in AS 65101 and AS 65201 is up.
Which configuration resolves the issue?
Refer to the exhibit After a misconfiguration by a junior engineer, the console access to router A is not working Which configuration allows access to router A?
A)
B)
C)
D)
Refer to the exhibit.
An engineer is troubleshooting a TACACS problem.
Which action resolves the issue?
Which technique removes the outermost label of an MPLS-tagged packet before the packet is forwarded to an adjacent LER?
:582
Refer to the exhibit. Branch 2 hosts cannot receive dynamic IP addresses. Which action resolves the issue?
Refer to the exhibit. The authentication is not working as desired and the user drops into user-exec mode. Which configuration resolves the issue?
Refer to the exhibit.
The none area 0 routers in OSPF still receive more specific routes of 10.1.1.0.10.1.2.0.10.1.3.0 from area 0. Which action resolves the issue?
Which protocol must be secured with MD-5 authentication across the MPLS cloud to prevent hackers from introducing bogus routers?
Refer lo lhe exhibit. The Customer Edge rouler wants to use AS 100 as the preferred ISP for all external routes and ISP-2 as a backup.
After this configuration, all the backup routes have disappeared from the BGP table on the Customer Edge router. Which set of configurations resolves the issue on the Customer Edge router?
A)
B)
C)
D)
The network administrator configured CoPP so that all routing protocol traffic toward the router CPU is
limited to 1 mbps. All traffic that exceeds
this limit must be dropped. The router is running BGP and OSPF Management traffic for Telnet and SSH
must be limited to 500kbps.
access-list 100 permit tcp any any eq 179
access-list 100 permit tcp any any range 22 23
access-list 100 permit ospf any any
!
class-map CM-ROUTING
match access-group 100
class-map CM-MGMT
match access-group 100
!
policy-map PM-COPP
class CM-ROUTING
police 1000000 conform-action transmit
class CM-MGMT
police 500000 conform-action transmit
!
control-plane
service-policy output PM-COPP
No traffic is filtering through CoPP,which is resulting in high CPU utilization,which configuration resolves
the issue ?
Refer to the exhibit. An engineer is investigating an OSPF issue reported by the Cisco DNA Assurance Center. Which action resolves the issue?
Which router translates the customer routing information into VPNv4 routes to exchange VPNv4 routes with other devices through MP-BGP?
In a DMVPN network, the Spoke1 user observed that the voice traffic is coming to Spoke2 users via the hub router. Which command is required on both spoke routers to communicate directly to one another?
Refer to the exhibit. A network engineer troubleshooting a packet drop problem for the host 172.16.100.5 notices that only one link is used and installed on the routing table, which saturates the bandwidth. Which action must the engineer take to resolve the high bandwidth utilization problem and share the traffic toward this host between the two available links?
:589
Aswitchhas been configured to provide DHCP relay on VLAN 100 to a server with an IP address of 10.1.1.1. The DHCP server is sending syslog reports of multiple TFTP requests that also originate from the switch. As a result, the server CPU exceeded a configured threshold. Which action does the network administrator recommend to bring the server CPU threshold down?
Which two technologies optimize MPLS infrastructure using bandwidth protection services when experiencing slow response7 (Choose two.)
Refer to the exhibit. An engineer configured router R3 to redistribute the prefix 10.10.10.0/24 from OSPF into EIGRP R1 has no connectivity to the prefix. Which action enables receipt of prefixes on R1?
Refer to the exhibit. Not all connected and static routes of router B are received by router A even though EIGRP neighborship is established between the routers. Which configuration resolves the issue?
A)
B)
C)
D)
Refer to the exhibit. An administrator must upload the packages conf Me to an FTP server. However, the FTP server rejected anonymous service and required users to authenticate What are the two ways to resolve the issue? (Choose two.)
Refer to the exhibit.
AS111 is receiving its own routes from AS200 causing a loop in the network. Which configuration provides loop prevention?
A)
B)
C)
D)
Refer to the exhibit.
A network engineer is adding a new spoke router into an existing DMVPN Phase 3 tunnel with a hub router to provide secure communication between sites Which additional configuration must the engineer apply to enable the tunnel to come up?
Refer to the exhibit EIGRP adjacency between router A and router C is not working as expected Which two configurations resolve the issue? (Choose two )
A)
B)
C)
D)
E)
Refer to the exhibit.
With the partial configuration of a router-on-a-stick. Clients in VLAN 10 on Gi2 cannot obtain IP configuration from the central DHP server is reachable by a successful ping from the route. Which action resolves the issue?
Refer to the exhibit.
Users report that IP addresses cannot be acquired from the DHCP server. The DHCP
server is configured as shown. About 300 total nonconcurrent users are using this DHCP server, but none of them are active for more than two hours per day. Which action fixes the issue within the current resources?
Refer to the exhibit.
The Internet traffic should always prefer Site-A ISP-1 if the link and BGP connection are up; otherwise, all Internet traffic should go to ISP-2 Redistribution is configured between BGP and OSPF routing protocols and it is not working as expected. What action resolves the issue?
Which two features are required for MPLS forwarding on which types of routers? (Choose two.)
Refer to the exhibit. An engineer is trying to log in to R1 via R3 loopback address. Which action resolves the issue?
An engineer must establish a connection between two CE routers for two customers with overlapping IP addresses Customer_a is connected to interfaces Gig0/0, and Customer_b is connected to interfaces Gig0/1. Routers CE1 and CE2 are configured as follows:
Drag and drop the code snippets from the right onto the boxes in the configuration to establish the needed connection. Snippets may be used more than once.
Refer to the exhibit.
An error message "an OSPF-4-FLOOD_WAR” is received on SW2 from SW1. SW2 is repeatedly receiving its own link-state advertisement and flushes it from the network. Which action resolves the issue?
Refer to the exhibit.
The AP status from Cisco DNA Center Assurance Dashboard shows some physical connectivity issues from access switch interface G1/0/14. Which command generates the diagnostic data to resolve the physical connectivity issues?
Refer to the exhibit An engineer is troubleshooting an OSPF adjacency issue between directly connected routers R1 and R2 Which configuration resolves the issue?
A)
B)
C)
D)
Refer to the exhibit An engineer must connect the Reno and Detroit spokes using DMVPN phase 2 Hub tunnel configuration is
Which configuration accomplishes the task?
Refer to the exhibit.
During ISP router maintenance, the network produced many alerts because of the flapping interface. Which configuration on R1 resolves the issue?
:576
Refer to the exhibit. R1 and R2 have been configured where the neighbor relationship must be authenticatedusmgMD5:
The neighbor relationship is not coming up. Which configuration resolves the issue?
Refer to the exhibit.
R4 is experiencing packet drop when trying to reach 172.16.2.7 behind R2. Which action resolves the issue?
Refer to the exhibit.
An engineer must block access to the console ports for all corporate remote Cisco devices based on the recent corporate security policy but the security team stilt can connect through the console port. Which configuration on the console port resolves the issue?
:587
Which IP precedence value does BFD use to prioritize traffic within an infrastructure device?
Refer to the exhibit. An engineer implements uRPF to increase security and stop incoming spoofed IP packets. Some asymmetrically routed packets are also blocked after the configuration. Which command resolves the issue?
Refer to the exhibit A customer reported an issue with a fiber link failure between RC and RE Users connected through the spoke location face disconnection and packet drops with the primary email server (172.16.16.1) but have no issues with the backup email server (172.16.26.1). All the router loopback IPs are advertised through the OSPF protocol. Which configuration resolves the issue?
Refer to the exhibit. Which configuration is required for R2 to get the IP address from the DHCP server?
Refer to the exhibit R2 has been receiving routes from R4 that originated outside AS300 A network engineer configured an AS-Path ACL to avoid adding these routes to the R2 BGP table but the routes are still present in the R2 routing table Which action resolves the issue?
Refer to the exhibit An enterprise operations team must monitor all application server traffic in the data center The team finds that traffic coming from the hub site from R3 and R6 rs monitored successfully but traffic destined to the application server is not monitored Which action resolves the issue?
A)
B)
C)
D)
Refer to the exhibit. The ISP router is fully configured for customer A and customer B using the VRF-Lite feature. What is the minimum configuration required for customer A to communicate between routers A1 and A2?
:591
Refer to the exhibit Which action fixes the OSPF routes redistribution into EIGRP?
Refer to the exhibit.
Mutual redistribution is enabled between RIP and EIGRP on R2 and R5. Which configuration resolves the routing loop for the 192.168.1.0/24 network?
Refer to the exhibit. AS 111 mut not be used as a transit AS, but ISP-1 is getting ISP-2 routes from AS 111. Which configuration stops Customer AS from being used as a transit path on ISP-1?
Refer to the exhibit The SNMP server with IP address 172.16 4 4 cannot access host router A Which configuration command on router A resolves the issue?
Refer to the exhibit The enterprise users fail to authenticate with the TACACS server when a direct fiber link fails between RB and RD The NOC team observes
Users connected on AS65201 fail to authenticate with TACACS server 192 168 1 1
Users connected on AS65101 successfully authenticate with TACACS server 192 168 1 1
All AS65101 and AS65201 users are configured to authenticate with the TACACS server
Which configuration resolves the issue?
A)
B)
C)
D)
Refer to the exhibit.
To provide reachability to network 10.1.1.0 /24 from R5, the network administrator redistributes EIGRP into OSPF on R3 but notices that R4 is now taking a ........... path through R5 to reach 10.1.1.0/24 network. Which action fixes the issue while keeping the reachability from R5 to 10.1.1.0/24 network?
Refer to the exhibit.
R1 is connected with R2 via GigabitEthernet0/0, and R2 cannot ping R1. What action will fix the issue?
An engineer is troubleshooting on the console session of a router and turns on multiple debug commands. The console screen is filled with scrolling debug messages that none of the commands can be verified if entered correctly or display any output. Which action allows the engineer to see entered console commands while still continuing the analysis of the debug messages?
Refer to the exhibit. Which action restores the routes from neighbors while still filtering 1.1.1.0/24?
Refer to Exhibit.
The network administrator configured the branch router for IPv6 on the E0/0 interface. The neighboring router is fully configured to meet requirements, but the neighbor relationship is not coming up. Which action fixes the problem on the branch router to bring the IPv6 neighbors up?
Refer to Exhibit.
Traffic from the branch network should route through HQ R1 unless the path is unavailable. An engineer tests this functionality by shutting down interface on the BRANCH router toward HQ_R1 router but 192.168.20.0/24 is no longer reachable from the branch router. Which set of configurations resolves the issue?
When configuring Control Plane Policing on a router to protect it from malicious traffic, an engineer observes that the configured routing protocols start flapping on
that device. Which action in the Control Plane Policy prevents this problem in a production environment while achieving the security objective?
Refer to the exhibit.
PC-2 failed to establish a Telnet connection to the terminal server. Which configuration resolves the issue?
Refer to the exhibit. R2 has two paths to reach 192.168.13.0/24. but traffic is sent only through R3. Which action allows traffic to use both paths?
Exhibit:
Bangkok is using ECMP to reach to the 192.168.5.0/24 network. The administrator must configure Bangkok in such a way that Telnet traffic from 192.168.3.0/24 and192.168.4.0/24 networks uses the HongKong router as the preferred router. Which set of configurations accomplishes this task?
Which two protocols work in the control plane of P routers across the MPLS cloud? (choose two)
Drag and drop the actions from the left into the correct order on the right to configure a policy to avoid following packet forwarding based on the normal routing path.
Refer to the exhibit.
The administrator can see the traps for the failed login attempts, but cannot see the traps of successful login attempts. What command is needed to resolve the issue?
Refer to the exhibit. The engineer configured and connected Router2 to Router1. The link came up but could not establish a Telnet connection to Router1 IPv6 address of 2001:DB8::1. Which configuration allows Router2 to establish a Telnet connection to Router1?
Refer to Exhibit.
A network administrator added one router in the Cisco DNA Center and checked its discovery and health from the Network Health Dashboard. The network administrator observed that the router is still showing up as unmonitored. What must be configured on the router to mount it in the Cisco DNA Center?
An engineer configured policy-based routing for a destination IP address that does not exist in the routing table. How is the packet treated through the policy for configuring the set ip default next-hop command?
Which configuration feature should be used to block rogue router advertisements instead of using the IPv6 Router Advertisement Guard feature?
Refer to the exhibit.
A network administrator configured an IPv6 access list to allow TCP return frame only, but it is not working as expected. Which changes resolve this issue?
Refer to the exhibit.
An engineer configured BGP between routers R1 and R3 The BOP peers cannot establish neighbor adjacency to be able to exchange routes. Which configuration resolves this issue?
Refer to the exhibit.
The neighbor relationship is not coming up Which two configurations bring the adjacency up? (Choose two)
Refer to the exhibit.
When monitoring an IPv6 access list, an engineer notices that the ACL does not have any hits and is causing unnecessary traffic to pass through the interface Which command must be configured to resolve the issue?
Refer to the exhibit. A network administrator configured mutual redistribution on R1 and R2 routers, which caused instability in the network. Which action resolves the issue?
Refer to the exhibit. The DHCP client is unable to receive an IP address from the DHCP server RouterB is configured as follows:
Interface fastethernet 0/0
description Client DHCP ID 394482431
Ip address 172 31 11 255 255.255 0
!
ip route 172.16.1.0 255 255 255.0 10.1.1.2
Which command is required on the fastethernet 0/0 interface of RouterB to resolve this issue?
Refer to the exhibit. The administrator configured route advertisement to a remote low resources router to use only the default route to reach any network but failed. Which action resolves this issue?
Refer to the exhibit.
A network administrator configured mutual redistribution on R1 and R2 routers, which caused instability in the network. Which action resolves the issue?
Refer to the exhibit.
All the serial between R1, R2, and R3 have the Same bandwidth. User on the 192.168.1.0/24 network report slow response times while they access resource on network 192.168.3.0/24. When a traceroute is run on the path. It shows that the packet is getting forwarded via R2 to R3 although the link between R1 and R3 is still up. What must the network administrator to fix the slowness?
An engineer configured a Cisco router to send reliable and encrypted notifications for any events to the management server. It was noticed that the notification messages are reliable but not encrypted. Which action resolves the issue?
In which two ways does the IPv6 First-Hop Security Binding Table operate? (Choose two.)
Refer to Exhibit:
AS 111 wanted to use AS 200 as the preferred path for 172.20.5.0/24 and AS 100 as the backup. After the configuration, AS 100 is not used for any other routes. Which configuration resolves the issue?
Refer to the exhibit. The OSPF neighbor relationship is not coming up What must be configured to restore OSPF neighbor adjacency?
Refer to the exhibit.
AS65510 iBGP is configured for directly connected neighbors. R4 cannot ping or traceroute network 192 168.100.0/24 Which action resolves this issue?
Clients on ALS2 receive IPv4 and IPv6 addresses but clients on ALS1 receive only IPv4 addresses and not IPv6 addresses. Which action on DSW1 allows clients on ALS1 to receive IPv6 addresses?
An engineer configured a DHCP server for Cisco IP phones to download its configuration from a TFTP server, but the IP phones failed to toad the configuration What must be configured to resolve the issue?
Refer to the exhibit.
The R1 and R2 configurations are:
The neighbor is not coming up. Which two sets of configurations bring the neighbors up? (Choose two.)
Refer to the exhibit.
Which two actions should be taken to access the server? (Choose two.)
Refer to the exhibit.
A client is concerned that passwords are visible when running this show archive log config all.
Which router configuration is needed to resolve this issue?
Refer to the exhibit.
An engineer wanted to set a tag of 30 to route 10 1.80.65/32 but it failed How is the issue fixed?
Refer to the exhibit.
The network administrator can see the DHCP discovery packet in R1. but R2 is not replying to the DHCP request. The R1 related interface is configured with the DHCP helper address. If the PC is directly connected to the FaO/1 interface on R2, the DHCP server assigns as IP address from the DHCP pool to the PC. Which two commands resolve this issue? (Choose two.)
Refer to the exhibit.
Which interface configuration must be configured on the HUB router to enable MVPN with mGRE mode?
Refer to the exhibit. An engineer has successfully set up a floating static route from the BRANCH router to the HQ network using HQ_R1 as the primary default gateway When the g0/0 goes down on HQ_R1, the branch network cannot reach the HQ network 192.168.20.0/24. Which set of configurations resolves the issue?
Refer to the exhibit. The network administrator configured the branch router for IPv6 on the E 0/0 interface The neighboring router is fully configured to meet requirements, but the neighbor relationship is not coming up. Which action fixes the problem on the branch router to bring the IPv6 neighbors up?
Refer to the exhibit.
A company with autonomous system number AS65401 has obtained IP address block 209.165.200.224/27 fro, ARIN. The company needed more IP addresses and was assigned block209.165.202.128/27 from ISP2. An engineer is ISP1 reports they are receiving ISP2 routes from AS65401. Which configuration onR1 resolves the issue?
A)
B)
C)
D)
Refer to the exhibits.
When DMVPN is configured, which configuration allows spoke-to-spoke communication using loopback as a tunnel source?
Refer to the exhibit.
An IPv6 network was newly deployed in the environment and the help desk reports that R3 cannot SSH to the R2s Loopback interface. Which action resolves the issue?
Refer to the exhibit.
Troubleshoot and ensure that branch B only ever uses the MPLS B network to reach HQ. Which action achieves this requirement?
An engineer configured two routers connected to two different service providers using BGP with default attributes. One of the links is presenting high delay, which causes slowness in the network. Which BGP attribute must the engineer configure to avoid using the high-delay ISP link if the second ISP link is up?
Refer to the exhibit.
While troubleshooting an EIGRP neighbor adjacency problem, the network engineer notices that the interface connected to the neighboring router is not participating in the EIGRP process. Which action resolves the issues?
Refer to the exhibit.
The network administrator must mutually redistribute routes at the Chicago router to the LA and NewYork routers. The configuration of the Chicago router is this:
After the configuration, the LA router receives all the NewYork routes, but NewYork router does not receive any LA routes. Which set of configurations fixes the problem on the Chicago router?
A)
B)
C)
D)
What are two purposes of using IPv4 and VPNv4 address-family configurations in a Layer 3 MPLS VPN? (Choose two.)
Exhibit:
An engineer configured R2 and R5 as route reflectors and noticed that not all routes are sent to R1 to advertise to the eBGP peers. Which iBGP routers must be configured as route reflectors to advertise all routes to restore reachability across all networks?
Refer to the exhibit.
The OSPF routing protocol is redistributed into the BGP routing protocol, but not all the OSPF routes are distributed into BGP Which action resolves the issue?
Refer to the exhibit.
A network administrator is discovering a Cisco Catalyst 9300 and a Cisco WLC 3504 in Cisco DNA Center. The Catalyst 9300 is added successfully However the WLC is showing [ error "uncontactable" when the administrator tries to add it in Cisco DNA Center. Which action discovers WLC in Cisco DNA Center successfully?
Refer to the exhibit. The Los Angeles and New York routers are receiving routes from Chicago but not from each other. Which configuration fixes the issue?
Refer to the exhibit.
The Math and Science departments connect through the corporate. IT router but users in the Math department must not be able to reach the Science department and vice versa Which configuration accomplishes this task?
An engineer configured SNMP notifications sent to the management server using authentication and encrypting data with DES. An error in the response PDU is received as "UNKNOWNUSERNAME. WRONGDIGEST". Which action resolves the issue?
Refer to the exhibit.
Which subnet is redistributed from EIGRP to OSPF routing protocols?
When provisioning a device in Cisco DNA Center, the engineer sees the error message “Cannot select the device. Not compatible with template”.
What is the reason for the error?
Refer to the exhibit.
An engineer has configured DMVPN on a spoke router. What is the WAN IP address of another spoke router within the DMVPN network?
Refer to the exhibit.
AAA server 10.1.1.1 is configured with the default authentication and accounting settings, but the switch cannot communicate with the server Which action resolves this issue?
TESTED 06 Dec 2025
Graphical user interface, application Description automatically generated
Graphical user interface, chart Description automatically generated
Table Description automatically generated
Text, table Description automatically generated
