After connecting a new server to interface Te 1/0/1 and configuring the port, you notice that the device is only showing up in the default VLAN 1 as shown in the exhibit.
interface TenGigabitEthernet 1/0/1
fabric isl enable
fabric trunk enable
switchport
switchport mode trunk
switchport trunk allowed vlan add 10
switchport trunk tag native-vlan
spanning-tree shutdown
no shutdown
!
show mac-address-table:
VlanId Mac-address Type State Ports
1 1234.5678.90ff Dynamic Active Te 1/0/1
You did not enable tagging on the server and now need to alter the interface configuration to force all frames from the server to be tagged for VLAN 10.
Which interface configuration would allow untagged frames from the server to be on VLAN 10?
One of the switches in your Brocade VCS Fabric in logical chassis mode needs to be replaced. After configuring the replacement switch with the same VCS RBridge ID of the faulty switch, you attempt to replace the faulty switch with a new one but find the switch is segmented from the fabric.
Which two steps should be completed to replace the faulty switch? (Choose two.)
You are an administrator at a cloud-based provider. You need a solution that provides L3 multi-tenancy to enable separate resources to be used by your customers.
Which feature would resolve this problem?
You are configuring OSPF in a Brocade VCS Fabric. The implementation will integrate with an existing OSPF network. The fabric is in logical chassis mode.
Referring to the exhibit, which three actions are correct? (Choose three.)
You want to form a single link aggregation group between a third-party switch and multiple Brocade VDX switches.
Which two conditions must be met? (Choose two.)
During a network outage, several RBridges in VCS Logical Chassis mode were disconnected from the rest of the network. During this time, some configuration changes were made to those switches.
When the network connection between the separated switches is repaired, what will occur?
You want to implement VRRP-E between a Brocade VDX 6740, and a Brocade VDX 6730 with the protocol vrrp command.
Which two statements are true? (Choose two.)
A customer has a Brocade VDX 8770 and wants to implement policy based routing (PBR).
ip access-list standard acl1
seq 10 permit 1.1.1.1 255.255.255.255
seq 20 deny 11.11.11.11 255.255.255.255
!
ip access-list standard acl2
seq 10 permit 2.2.2.2 255.255.255.255
route-map brocade1 permit 10
match ip address acl acl1
set ip interface null0
set ip vrf brocade1 next-hop 3.3.3.3
!
route-map brocade1 permit 20
match ip address acl acl2
set ip next-hop 4.4.4.4
set ip vrf brocade1 next-hop 3.3.3.5
!
route-map brocade1 permit 30
set ip interface null0
Based on the configuration shown in the exhibit, what will happen to traffic coming from 2.2.2.2?
Which three are required for a Brocade VDX 6730 to join an existing Brocade VCS Fabric with centralized management? (Choose three.)
To form a Brocade VCS Fabric between a Brocade VDX 6730 and a VDX 6740T, what is required?
Your customer is using Brocade Network Advisor as a trap recipient for a Brocade VCS Fabric. A Brocade VDX is discovered and the customer is testing SNMP traps by removing the power supply. You are not receiving traps.
Which three actions will determine the problem? (Choose three.)
Exhibit:
switch# show port-channel 300
LACP Aggregator: Po 300 (vLAG)
Aggregator type: Standard
Ignore-split is enabled
Member rbridges: rbridge-id: 51 (2) rbridge-id: 52 (2)
Admin Key: 0010 - Oper Key 0010
Partner System ID - 0x8000,01-e0-52-00-00-02
Partner Oper Key 0010
Member ports on rbridge-id 51:
Link: Te 51/0/31 (0x19180E801C) sync: 1
Link: Te 51/0/32 (0x19180F001D) sync: 1
Exhibit:
Referring to the exhibit, what information is determined?
Exhibit:
sw0(conf-if-te-0/5)# channel-group 100 mode active type standard
%%Error: A switchport or a router port cannot be aggregated
Exhibit:
Referring to the exhibit, what is the cause of the error when applying a port channel to an interface?
You are attempting to merge two Brocade VDX switches, both running in fabric mode, but they segment.
sw0# show fabric islports
Name: sw0
Type: 96.5
State: Online
Role: Fabric Principal
VCS Id: 10
Config Mode:Local-only
Rbridge-id: 4
WWN: 10:00:00:05:33:91:48:f7
FCF MAC: 00:05:33:91:48:f7
sw0# show fabric islports
Name: sw0
Type: 96.5
State: Online
Role: Fabric Principal
VCS Id: 10
Config Mode:Distributed
Rbridge-id: 20
WWN: 10:00:00:05:33:90:92:e4
FCF MAC: 00:05:33:90:92:e4
Referring to the exhibit, what is the reason?
You need to deploy several FCoE initiators to communicate to existing FC SAN attached targets.
Which two statements are true about deploying the solution? (Choose two.)
Which two statements are true when traffic is transmitted over a fabric ISL trunk? (Choose two.)
You want to determine which link aggregation mode you should choose between a pair of Brocade VDX switches in different VCS Fabrics. You want to use frame-based distribution.
Which action should you perform?
After implementing a topology that requires edge loop detection, you detected a broadcast storm within the environment.
Which two required parameters must be configured? (Choose two.)
You are attempting to merge two Brocade VDX switches, both running in fabric mode, but they segment.
sw0# show fabric islports
Name: sw0
Type: 96.5
State: Online
Role: Fabric Principal
VCS Id: 10
Config Mode:Distributed
Rbridge-id: 4
WWN: 10:00:00:05:33:91:48:f7
FCF MAC: 00:05:33:91:48:f7
sw0# show fabric islports
Name: sw0
Type: 96.5
State: Online
Role: Fabric Principal
VCS Id: 10
Config Mode:Distributed
Rbridge-id: 4
WWN: 10:00:00:05:33:90:92:e4
FCF MAC: 00:05:33:90:92:e4
Referring to the exhibit, what is the reason?
Which two port profile attributes would be assigned before applying the port profile to an interface? (Choose two.)
Which extension to the TRILL protocol allows a Brocade VCS Fabric to scale beyond 4096 VLANs?
Your customer adds two Brocade VDX 6740s to an existing Brocade VCS Fabric in logical chassis mode with VCSID 11. After enabling logical chassis mode on both new switches, a connection is made between the two switches. A cable is then connected between one of the switches of the logical chassis. The ISL to the logical chassis is isolated with an Exchange Switch Capabilities (ESC) error, detailing a database mismatch.
What caused the problem?