CDCS Sample Questions Answers

NFPA 75 (IT equipment rooms) recommends pre-action sprinklers for data processing spaces to minimize accidental water discharge risk; wet-pipe is generally discouraged directly over IT hardware.

High relative humidity (above 80%) creates a serious risk for corrosion of electronic contacts, printed circuit boards (PCBs), and metallic components. Moisture in the air condenses more easily, especially when surfaces are cooler than ambient dew point. This can lead to oxidation of connectors, degradation of solder joints, and eventual failures in ICT hardware.

Electrostatic discharge (ESD) risks, by contrast, increase at low humidity (below 30%) because dry air promotes charge buildup. Therefore, option C is incorrect here. Similarly, option D (cooling risk from wet-bulb temperature) applies to evaporative cooling efficiency, not directly to ICT risk.

ASHRAE recommends data centers maintain RH between 40–60% for optimal reliability. Values above 80% RH are considered outside the recommended operating envelope and significantly increase the risk of corrosion, especially in the presence of airborne contaminants like sulfur dioxide (SO₂) or hydrogen sulfide (H₂S).

Therefore, the verified risk at 85% RH is corrosion-related degradation.

According to ASHRAE TC 9.9 Thermal Guidelines (2016), the recommended intake temperature range for Class A1 ICT equipment is 18–27 °C (64–81 °F). The allowable lower limit is 15 °C (59 °F). Setting supply to 4 °C (39 °F) falls far below these limits.

Operating at such low temperatures would:

Cause condensation risk when surfaces drop below dew point.

Create severe energy inefficiency, as chillers would run at extremely low setpoints.

Possibly damage hardware due to thermal shock.

Options A and B are misleading—system capability or dew point alone does not override ASHRAE guidelines. Option D is incorrect since 20 °C is a common design target, not a requirement.

Thus, supplying 4 °C is not acceptable.

ASHRAE recommends temperature and humidity be measured in the cold aisle, in front of racks, at approximately 1.5 m above the floor (average human working height) and 0.3–0.5 m from the rack face. This location captures the environmental conditions experienced at the IT equipment air intake, while still representing facility-level conditions (not single device-level).

Option A and C (at 50 mm intake/rear) are too close to individual servers and suited only for rack-level monitoring, not facility monitoring.

Option D (rear measurement) reflects exhaust air, not intake, and thus cannot be used to control environmental setpoints.

Maintaining measurement at standardized facility locations allows comparisons against ASHRAE’s recommended and allowable ranges (18–27 °C for Class A1 environments, 40–60% RH).

MCBs (Miniature Circuit Breakers) are characterized by their tripping curves:

B-Curve: Trips at 3–5 × rated current; suitable for resistive loads.

C-Curve: Trips at 5–10 × rated current; suitable for mixed loads including ICT equipment with moderate inrush current.

D-Curve: Trips at 10–20 × rated current; used for heavy inductive loads like motors.

A-Curve: Very sensitive, rarely used outside specialty electronics.

Since ICT equipment like servers and network devices have moderate inrush currents (from power supplies), the recommended breaker is C-Curve. It balances protection against nuisance tripping while still ensuring fault clearance.

ASHRAE TC 9.9 recommends using dust deposition coupons (also called reactivity coupons) to measure particulate contamination over time. These are small, standardized metallic plates exposed to the air that collect dust and contaminants. After a set period, they are analyzed for chemical corrosion rates and particulate buildup.

Option A (handheld analyzers) gives spot counts of airborne particles but does not capture long-term corrosive deposition risk.

Option C only samples underfloor plenum dust, not actual IT environment contamination.

Option D (opening equipment) is invasive and risks voiding warranties.

Coupons provide standardized, passive, and reliable monitoring of contamination over months, making them the preferred method.

With infrequent/short outages, Standby (Emergency Standby Power, ESP) generators are appropriate; N+1 mitigates failure-to-start risk and supports concurrently maintainable designs.

Network administration in structured cabling is governed by ANSI/TIA-606-B, which defines requirements for cable and asset administration, labeling, documentation, and record-keeping. It specifies how pathways, spaces, and cabling should be identified and labeled to ensure proper lifecycle management.

ANSI/TIA-568 covers cabling performance standards, not administration.

ISO/IEC 30129 relates to data center facilities and infrastructure but not cable management.

ASHRAE focuses on thermal management, not cabling.

Proper administration is critical in data centers because high cable density can lead to operational issues, troubleshooting delays, and risk of downtime if poorly managed. By enforcing labeling schemes, color codes, and database-driven records, ANSI/TIA-606 supports operational excellence and compliance with ANSI/TIA-942.

Cooling airflow (CFM) can be calculated from:

Where P = IT load.

So approximately 500 CFM is required.

1,500 and 1,000 CFM are too high.

160 CFM is far too low.

Therefore, the correct answer is ~500 CFM.

When the window area exceeds the maximum exposed area specified for fire-rated glass, it is necessary to split the window into sections that comply with the fire rating requirements. This means creating smaller sections that are each within the 3 sqm/32 sqft limit and using fire-rated frames to ensure that the entire assembly meets fire safety standards. This approach maintains the fire-rated integrity of the glass, while allowing for larger window areas.

Detailed Explanation:

Fire-rated glass is designed to contain fire and prevent it from spreading. If the window exceeds the maximum exposed area defined by the supplier, the integrity of the fire-rated glass could be compromised. By dividing the window into compliant sections with fire-rated frames, you ensure that each pane performs as intended in the event of a fire. Fire-rated frames help maintain the fire resistance across the entire assembly, making this option the best for safety and compliance.

EPI Data Center Specialist References:

EPI recommends adhering strictly to fire safety standards, especially when using materials like fire-rated glass. The guidelines emphasize that modifications should always respect the manufacturer’s specifications to ensure the system remains effective in containing and preventing the spread of fire.

Raised floor tiles with air deflectors or louvers are typically heavier than standard tiles due to the additional materials and mechanisms used to direct airflow. The added weight can pose challenges for installation and adjustment, and consideration must be given to the floor’s load capacity and ease of maintenance.

Detailed Explanation:

Tiles with deflectors or louvers help direct airflow, enhancing cooling efficiency by focusing cool air where needed. However, these tiles are often heavier, which can affect handling and require reinforced raised floor systems. It's essential to factor in the weight for any floor tile replacements or installations to ensure they are compatible with the raised floor's structural capacity.

EPI Data Center Specialist References:

EPI data center design training mentions the potential impact of heavy tiles on floor handling and load capacity. Data center operators need to plan for safe handling and load-bearing capacity when using such specialized tiles.

In a data center with noise levels of 91 dB (A), employers are indeed required to take precautions to protect personnel, as this level exceeds commonly accepted safety thresholds for occupational noise exposure. Regulations, such as those from the Occupational Safety and Health Administration (OSHA) or similar agencies, mandate specific controls and protections for environments with high noise levels.

Detailed Explanation:

Noise levels above 85 dB (A) typically trigger requirements for hearing conservation programs. At 91 dB (A), steps like providing ear protection, conducting regular noise assessments, and possibly implementing engineering controls to reduce noise should be taken. Extended exposure to such levels can lead to hearing loss, so regulatory compliance ensures both immediate and long-term protection for personnel.

EPI Data Center Specialist References:

EPI guidelines for data center safety address noise exposure as part of the environmental safety measures. EPI recommends adhering to local occupational health regulations, as excessive noise can harm personnel and affect operational efficiency due to potential health hazards.

Attenuation is the logarithmic ratio between input and output signals. For power, we use 10 log; for voltage or current, 20 log. Since EMF shielding is measured as field strength (V/m or A/m), power relationship is proportional to the square of field. Thus the correct attenuation calculation for shielding effectiveness is:

A black text on a white background AI-generated content may be incorrect.

where:

M = maximum permissible field strength

R = measured field strength after shielding

This ensures the shield reduces field intensity to below allowable limits.

For a cooling audit in a data center, it is essential to measure temperature and humidity where air enters the servers to accurately assess cooling performance. In this case, since all servers have a front-to-rear (F-R) airflow design, measuring at the front/intake of the server will provide a precise understanding of the cooling conditions that the equipment is experiencing.

Detailed Explanation:

Servers with a front-to-rear airflow design draw in cool air from the cold aisle at the front, which is then exhausted into the hot aisle at the rear. By measuring temperature and humidity 50 mm/2 inches from the front intake, you gather data on the air conditions right before it enters the servers, providing an accurate representation of the cooling environment as it directly impacts the equipment.

Measuring in the cold aisle at the front intake ensures that the readings reflect the actual conditions of the incoming air that the servers depend on for effective cooling. This approach is consistent with best practices for maintaining thermal conditions in a data center, as it helps confirm that the cooling systems are delivering air within the required temperature and humidity specifications.

EPI Data Center Specialist References:

According to the EPI Data Center Specialist curriculum, the optimal placement for temperature and humidity sensors is at the intake of the equipment in the cold aisle, as it directly correlates to the environmental conditions affecting the servers. This positioning allows for a more effective audit of cooling performance, which is critical for maintaining the reliability and efficiency of the data center’s operations.

Given the customer’s requirement to limit Total Harmonic Distortion (THDi) to below 3% and the presence of a 6-pulse SCR/Thyristor-based rectifier, an active harmonic filter is the best solution. A 6-pulse rectifier typically generates higher harmonic distortion, often exceeding 3%, especially under substantial loads like 80%. An active harmonic filter dynamically monitors and compensates for harmonic distortion, effectively reducing THDi and supporting a more power-efficient operation, aligning with the customer’s energy efficiency goals.

Detailed Explanation:

Passive harmonic filters can reduce harmonics but are less effective at maintaining low THDi levels under varying loads. Active filters offer real-time correction and can achieve lower THDi levels than passive filters, especially in systems with fluctuating loads or where strict harmonic limits are required. Installing an active harmonic filter will ensure compliance with the specified THDi limits and optimize power quality.

EPI Data Center Specialist References:

EPI guidance on power quality management recommends active harmonic filters for environments where strict THDi levels are necessary. Active filters offer better control over harmonic levels, supporting both compliance and operational efficiency.

High levels of H2S (hydrogen sulfide) gas contamination in a computer room are best addressed by installing air-scrubbers. Air-scrubbers can effectively filter out contaminants, including corrosive gases like H2S, ensuring clean air circulation and protecting sensitive IT equipment from potential corrosion and damage.

Detailed Explanation:

Air-scrubbers are designed to remove various airborne contaminants and are particularly useful in environments where corrosive gases are present. These systems use filters or chemical reactions to neutralize harmful substances, making them ideal for data centers that need to maintain high air quality for equipment reliability.

EPI Data Center Specialist References:

EPI guidelines suggest air-scrubbing technologies to remove contaminants that pose risks to electronic equipment, maintaining air quality and reducing corrosion risk.

In seismic-prone areas, cables should be tightly secured to racks and cable trays to minimize movement during seismic activity. Properly securing the cables prevents them from being damaged due to excessive motion, which could lead to outages or damage to connected equipment.

Detailed Explanation:

Loose cables can be vulnerable to shaking or sudden jolts during an earthquake, increasing the risk of disconnection or damage. By tightly organizing and securing cables, you ensure they remain in place, even during significant movement, thereby maintaining connection integrity and reducing the risk of physical damage.

EPI Data Center Specialist References:

EPI training includes considerations for data centers in seismic zones, advising that cables be firmly anchored to support structures to reduce movement and mitigate potential damage during seismic events.

Halocarbon agents such as FM-200 (HFC-227ea) and Novec-1230 (FK-5-1-12) are both defined under NFPA 2001 and ISO 14520 as clean agents, but their required design concentrations and physical properties differ. When calculating agent quantity, the minimum extinguishing concentration (MEC) and safety factor (S) must be taken into account. The S-factor is specific to each agent and reflects differences in molecular weight, density, and flame suppression chemistry.

For Novec-1230, the required design concentration is generally lower than for FM-200 (around 4.5–6% vs. 7–9%), but the calculation formula is the same except for substituting the correct S-factor. Therefore, you cannot reuse the exact formula parameters from FM-200; you must change the S-factor and apply Novec-1230’s physical constants.

This ensures compliance with NFPA 2001 Annex C, which provides correction formulas for room volume, temperature, and specific agent type. Using the wrong S-factor could result in underfilling or overfilling, compromising fire safety or increasing cost unnecessarily.

Hydrogen sulfide (H₂S) is a corrosive gas that readily reacts with metals, especially copper and silver found in circuit boards, connectors, and power supply components. Even at concentrations below human detection thresholds, H₂S can cause sulfidation corrosion leading to intermittent connections, failure of solder joints, and increased failure rates of electronic equipment.

ASHRAE Technical Committee 9.9 has documented multiple failures in data centers due to corrosive gases (notably sulfur-bearing compounds). Therefore, high humidity combined with H₂S presence accelerates this risk.

H₂S does not affect static flooring properties (B) or fire suppression agent chemistry (D). Option A is clearly incorrect as the risk is well-documented.

The cooling capacity of a raised floor tile is primarily influenced by the percentage of surface opening, the obstruction caused by the supporting construction, the pressure under the raised floor, and the damper construction. These factors dictate how much airflow can pass through the tile and how effectively cool air is distributed to the equipment in the data center.

Detailed Explanation:

The percentage of surface opening on a floor tile affects how much air can flow through, with larger openings allowing more airflow. Supporting structures beneath the floor can obstruct airflow, reducing cooling efficiency. Pressure under the raised floor impacts the velocity and volume of air that moves through the tile. Additionally, if dampers are installed, they control the airflow rate, which can be adjusted to meet specific cooling needs for the area.

EPI Data Center Specialist References:

EPI guidance on airflow management under raised floors emphasizes these factors as critical for effective cooling, especially in high-density areas. Ensuring unobstructed and adequate airflow helps maintain consistent cooling across equipment.

To calculate the cooling airflow requirement for ICT equipment, you can use the formula:

CFM=Power (kW)×3160ΔT(°F)\text{CFM} = \frac{\text{Power (kW)} \times 3160}{\Delta T (\text{°F})}CFM=ΔT(°F)Power (kW)×3160​

For equipment consuming 6 kW with a Delta-T of 20°F:

CFM=6×316020=948≈1,000 CFM\text{CFM} = \frac{6 \times 3160}{20} = 948 \approx 1,000 \, \text{CFM}CFM=206×3160​=948≈1,000CFM

Detailed Explanation:

This formula provides an estimate of the cubic feet per minute (CFM) of air required to cool the equipment based on its power consumption and the temperature difference (Delta-T) between intake and exhaust. The Delta-T represents the cooling effectiveness of the airflow.

EPI Data Center Specialist References:

EPI recommends using this calculation for determining airflow requirements in data centers, ensuring that cooling systems are adequately sized to maintain equipment within safe temperature limits.

An imbalance in load sharing between UPS systems connected in parallel can often result from unequal cable lengths to the common busbar. If the cabling from each UPS to the busbar varies significantly in length, it can lead to differences in impedance, resulting in uneven load distribution. Ensuring that cable lengths are consistent helps to balance the load sharing across the UPS systems.

Detailed Explanation:

Parallel UPS systems rely on uniform impedance to share loads evenly. Differences in cable lengths cause variations in resistance, leading to one or more UPS units carrying a disproportionate share of the load. Standardizing cable lengths ensures equal impedance, which promotes balanced load sharing and prevents one UPS from being overburdened, thus maintaining overall system reliability.

EPI Data Center Specialist References:

EPI guidelines recommend checking cable lengths when load imbalances occur in parallel UPS configurations. Ensuring equal lengths is a common method to resolve impedance issues that affect load distribution, which is critical for the stable operation of redundant power systems.

The server’s repeated overheating despite adequate intake and exhaust temperatures suggests that dust buildup inside the server may be impeding heat transfer. Dust accumulation can obstruct airflow within the server, insulate components, and disrupt the convection-based cooling systems that regulate internal temperatures, leading to overheating and potential hardware failures.

Detailed Explanation:

While the intake and exhaust temperatures appear within acceptable ranges, internal dust can reduce airflow and impede cooling efficiency, causing internal components to overheat despite seemingly normal ambient conditions. Regular cleaning and maintenance are critical for preventing dust-related issues, especially in high-powered equipment like a 5kW server.

EPI Data Center Specialist References:

EPI emphasizes regular maintenance to prevent dust buildup in data center equipment. Dust can significantly impact cooling efficiency and lead to overheating, which underlines the importance of routine cleaning for optimal server performance.

When shielding material reaches its saturation point, it can no longer effectively attenuate additional EMF. At saturation, the material’s ability to absorb or redirect magnetic fields is exhausted, meaning it cannot provide further shielding beyond this point. Additional EMF exposure would pass through the material without significant reduction.

Detailed Explanation:

Saturation occurs when the material’s magnetic domains are fully aligned with the magnetic field, leaving no capacity to absorb or deflect further EMF. This can happen with high EMF levels, beyond the material’s design limits, resulting in a breakdown of shielding effectiveness.

EPI Data Center Specialist References:

EPI guidelines on EMF management indicate that selecting appropriate shielding materials with sufficient capacity is essential to prevent saturation and ensure continuous protection. Saturation limits should be considered during design to avoid compromised shielding performance.

The data center life cycle is typically divided into four stages:

Design (scope, architecture, planning)

Implement (construction, installation, testing & commissioning)

Operate/Optimize (day-to-day operations, maintenance, continuous improvement)

Retire (decommissioning and migration)

Testing and commissioning occur in the Implement stage, after construction but before handover. This includes Integrated Systems Testing (IST), which validates that all systems (electrical, cooling, fire protection, telecom) perform to design intent and redundancy requirements.

Without commissioning, the data center cannot be certified or considered operational.

In computer rooms, replacing a wet pipe system with a pre-action system is advisable. Pre-action systems provide additional protection by requiring two triggers (e.g., heat and smoke) before water is released, minimizing the risk of accidental discharge and water damage, which is crucial for safeguarding sensitive IT equipment.

Detailed Explanation:

Wet pipe systems contain water in the pipes at all times, which poses a higher risk of accidental discharge. Pre-action systems, however, only fill the pipes with water upon detection of a fire, reducing the risk of water-related damage due to leaks or malfunctions. This approach is considered best practice for environments housing sensitive electronic equipment.

EPI Data Center Specialist References:

EPI advises using pre-action fire suppression in data centers to reduce risks associated with accidental water release, providing a safer and more controlled fire response that better protects critical infrastructure.

Battery charging current is typically sized at 10% of the total Ah capacity to ensure safe charging without overheating.

Charging Current=800Ah×0.1=80A

40 A or 60 A would undercharge, extending recovery time after discharge.

160 A would be too high, causing heat and reducing battery life.

Thus, 80 A is correct.

In locations with consistently cold temperatures, such as above the Arctic Circle, an airside economizer is the most energy-efficient cooling solution. Airside economizers use cool outside air to lower indoor temperatures, reducing or even eliminating the need for mechanical cooling. Given the consistently low temperatures, this method maximizes energy efficiency by leveraging natural cooling.

Detailed Explanation:

Airside economizers are ideal in environments where outside temperatures are consistently low. By drawing in and filtering cold outdoor air, they directly cool the indoor environment, thereby reducing energy consumption significantly compared to traditional air conditioning. This cooling approach aligns with energy efficiency goals by minimizing mechanical cooling demands.

EPI Data Center Specialist References:

EPI recommends the use of airside economizers in cold climates to achieve high energy efficiency, as they allow data centers to capitalize on ambient conditions for cooling, aligning with sustainability and cost-saving practices.

Electromagnetic fields are generated by current-carrying conductors. To minimize stray EMF, phase conductors should be physically close and balanced. A three-phase combined cable (all phase conductors and neutral in one sheath) ensures magnetic fields cancel each other due to phase opposition.

If phases are run separately (answer B), the separation increases loop area and magnetic field leakage. Single-phase cabling (A) is even worse because current does not balance across three phases. Bus bar trunking (C) provides physical support but often separates conductors, which may worsen EMF if not specifically shielded.

Therefore, the correct solution is three-phase combined cable (often XLPE-insulated). This design reduces EMF impact to within ANSI/TIA-942 and IEEE recommendations.

High dust levels in a computer room are often due to improperly fitted floorboards. When floorboards are not securely installed or do not fit tightly, they allow dust and particles from the subfloor to enter the room. In a data center, this can lead to high levels of dust that affect air quality and equipment performance.

Detailed Explanation:

Raised floors in data centers can accumulate dust and debris, especially if the floorboards are not properly sealed. Loose or improperly fitted floorboards allow contaminants from the subfloor to enter the data center environment, increasing the dust levels over time. Proper installation and maintenance of floor panels are essential to prevent dust infiltration and maintain clean conditions.

EPI Data Center Specialist References:

EPI training emphasizes proper flooring installation and maintenance to control air quality within data centers. Correctly fitted floorboards prevent dust accumulation from the subfloor, which helps protect sensitive equipment and maintains a cleaner environment.

Earth Leakage Protection is primarily installed to protect human lives by detecting and disconnecting power when a fault current flows to the ground. This type of protection is essential to avoid electrical shock hazards that could occur when insulation fails, or equipment is improperly grounded.

Detailed Explanation:

Earth leakage currents can occur due to insulation faults or accidental contact with live parts. Earth Leakage Protection systems, such as Residual Current Devices (RCDs), quickly detect these faults and disconnect the circuit to prevent harm to personnel. This is especially crucial in environments like data centers where high-powered equipment is continuously running and any electrical fault can pose significant safety risks.

EPI Data Center Specialist References:

EPI emphasizes that human safety is paramount in data center operations. Proper grounding and leakage protection are fundamental safety measures, and EPI guidelines align with this focus, underscoring the importance of protecting personnel from electrical hazards through appropriate safety systems.

Perforated tiles with integrated dampers are common in raised-floor data centers because they allow airflow regulation at the rack level. However, even when the damper is fully open, the mechanism inside the tile restricts airflow. This typically reduces the delivered airflow by around 10% compared to a non-dampered tile of the same type.

Option A is incorrect because dampers do not affect supply temperature; they only throttle volume.

Option B is wrong since dampers cannot increase volume—they only add resistance.

Option D is partially true that dampers help with temperature balancing, but the main effect (in open position) is volume reduction.

Thus, the technical impact of dampers in open position is a slight airflow reduction, usually quantified as ~10%.

From an efficiency standpoint, Unit B with a Sensible Heat Ratio (SHR) of 0.9 is preferable. A higher SHR indicates that a greater proportion of the air conditioner's capacity is dedicated to sensible cooling (temperature reduction) rather than latent cooling (moisture removal). In data centers, sensible cooling is more critical since IT equipment primarily generates heat without adding significant moisture.

Detailed Explanation:

An SHR of 0.9 means that 90% of the cooling capacity is used for sensible cooling, which is more efficient for environments like data centers where humidity control is typically less of a concern. Opting for an air conditioner with a higher SHR ensures that most of the cooling energy is focused on temperature reduction, making Unit B more efficient in this scenario.

EPI Data Center Specialist References:

EPI data center best practices recommend choosing cooling units with higher SHR values in data centers, as they better match the cooling needs of IT equipment. High SHR units improve cooling efficiency by concentrating on sensible heat removal, which is vital for maintaining the optimal thermal environment.