H35-481_V2.0 Sample Questions Answers

SCTP tracing result is not required to diagnose a low Internet access rate for a user. User performance testing can be used to collect information such as BLER (Block Error Rate) monitoring result, downlink RSRP (Reference Signal Received Power) monitoring result, and MCS (Modulation and Coding Scheme) count monitoring result. However, SCTP (Stream Control Transmission Protocol) tracing result is not required to diagnose a low Internet access rate. Reference: https://www.aricent.com/blog/user-performance-testing-for-5g/

5G Use Cases for Vertical China - 2021

https://www.gsma.com/greater-china/wp-content/uploads/2021/02/5G-Use-Cases-for-Vertical-China-2021-EN.pdf

Smart Manufacturing and Tactile Internet Based on 5G in Industry ...

https://www.mdpi.com/2079-9292/10/24/3175

Digital technologies for a new future

https://www.cepal.org/sites/default/files/publication/files/46817/S2000960_en.pdf

The GUI configuration mode in MAE-Deployment can be used to configure parameters in an MO and reconfigure a single NE. It cannot be used to configure parameters in multiple MOs or to batch reconfigure multiple NEs. According to the Huawei official documentation, "The GUI configuration mode can be used to configure parameters in an MO and reconfigure a single NE. However, it cannot be used to configure parameters in multiple MOs or to batch reconfigure multiple NEs."

After the PA reconfiguration of a 5G base station in SA networking, it is necessary to check whether cell-related alarms are reported, whether the 5G cell services are normal, and whether the PCI on the NR side has taken effect on the NE. These checks are necessary to ensure that the reconfiguration has been successful.

The statement "The start symbol of a front-loaded DMRS of a type B PDSCH is always the first symbol of PDSCH" is incorrect. In 5G NR, the start symbol of a front-loaded DMRS of a type B PDSCH can be configured as the first symbol of PDSCH or as the second symbol of PDSCH.

You can refer to the Huawei official documentation for HCIP-5G-RAN V2.0 certification and the 3GPP 5G NR standard (38.211, 38.212, 38.213) for more information on PDSCH DMRS, including the configurations of the front-loaded DMRS, the DMRS symbols and the optional and mandatory nature of it.

Here are some official references:

• Huawei HCIP-5G-RAN V2.0 certification page: https://e.huawei.com/en/certifications/hcip-5g-ran-v2-0
• 3GPP 5G NR standard: https://www.3gpp.org/specifications/5g-nr-specifications

The statement A is incorrect. The larger the subcarrier spacing [1], the shorter the symbol duration on each subcarrier, not the larger number of symbols. Statement B is also incorrect. The larger the subcarrier spacing [1], the larger the CP length and the more suitable it becomes for wide coverage. Statement C is correct. The smaller the subcarrier spacing, the lower the power spectral density. Statement D is incorrect. The larger the subcarrier spacing [1], the shorter the slot length.

1. A novel timing and frequency offset estimation algorithm for filtered ...

https://asp-eurasipjournals.springeropen.com/articles/10.1186/s13634-020-00696-1

Extended Cyclic Prefix - an overview | ScienceDirect Topics

https://www.sciencedirect.com/topics/engineering/extended-cyclic-prefix

5G NR Numerology - Subcarrier Spcaing (SCS) - Techplayon

http://www.techplayon.com/5g-nr-numerology-subcarrier-spcaing-scs/

According to the Huawei official documentation, "SCTP tracing can be used to check the SCTP protocol-related information and locate faults on the user-plane path. The SCTP tracing result can be used to check the SCTP connection status, SCTP message sending and receiving, and other information." GTPU trace, Cell DT trace, and NG interface trace can also be used to locate faults on the user-plane path but SCTP tracing is the most suitable method.