Click the exhibit button.
Which of the following would correctly configure routers R2, R3, and R4?
Click on the exhibit.
Given the contents of the Router LSA, which of the following best describes the local topology of the router?
Click on the exhibit.
Given the contents of the LSPs from routers R1 and R2, which of the following is TRUE?
Click on the exhibit.
The numbers beside the links are the metrics for that link.
Given the diagram, what path will traffic follow from router R1 to router R7, and from router R7 to router R1, if IS-IS is the routing protocol?
Click the exhibit button.
Router 2 advertises the network 192.168.3.0/24 to router R1 via IS-IS.
How can router R1 ensure that it discards the route?
Refer to the exhibit below.
R1 distributes its loopbacks into IS-IS and globally routed addresses are configured as shown. How many routes will R4 have in its IPv6 route table?
Which of the following LSA types stay within an OSPF area, and are not flooded outside of the area? Choose two answers.
Click the exhibit button.
In the topology shown, router R1 is an ASBR configured to export external routes to OSPF. Assuming that there are no stub networks, which of the following statements regarding Type 4 LSA generation is true?
Click the exhibit button. Assuming point-to-point links, which of the following statements is true?
Which of the following best describes the actions after an IS-IS router receives on a broadcast interface, a newer LSP than the one in its database?
Two IS-IS L1/L2 routers are in the same area on the same Ethernet segment. One of the routers is the DIS. How many adjacencies will be formed between them?
What are the types of networks supported on an Alcatel-Lucent 7750 SR for OSPF? (Choose 2)
What command allows analysis of the Dijkstra calculation on the Alcatel-Lucent 7750 SR?
Which of the following statements regarding OSPF routing updates on a multi-access network segment is true?
What command will show the OSPF neighbors, and their status on the Alcatel-Lucent 7750 SR?
When an OSPF adjacency is stuck in the "ExchStart" state, what is the most likely cause?
In an OSPF Hello packet what fields must match all neighbor routers on the segment? (Choose 3)
In an OSPF environment, what must a router receive after it sends out an update?
An OSPF adjacency is stuck in the exstart state. What is the most likely cause?
Click on the exhibit.
A service provider is deploying a 6 over 4 tunnel to connect a customer's corporate IPv6 network to all devices at the branch office as shown in the exhibit.
Which command is used to create the route to the branch office network on PE1?
A static route needs to be configured with a next-hop that is NOT directly connected to the router. Which of the following must be TRUE?
When a router performs the SPF calculation, which router is used as the root of the shortest path tree?
Click on the exhibit.
Given the contents of the Router LSA, which of the following best describes the local topology of the router?
An Alcatel-Lucent 7750 SR has a port with the MAC address of 00;03:FA:AC:77: AF. The port is bound to an interface. If IPv6 is then enabled on that interface .what will the link-local address be?
Click on the exhibit.
An OSPFv3 router is attached to a non-OSPF domain that includes networks 2001:DB8:8::/64.2001 .DB8:9::/64 and 2001 :DB8:A::/64. Other routers in the OSPF domain see the prefix 2001, DB8:8::/64, but not the other two prefixes.
What could cause this?
Which OSPFv3 LSA type is generated by an ABR to advertise prefixes from one area to another?
Two IS-IS routers are exchanging Hello packets with different authentication types. Which of the following is TRUE?
Which of the following is a valid IPv6 address equivalent to 2001:0da8:0000:0000:0024:0000:4ab9:0300?
Click on the exhibit.
192.168.3.1 is a loopback interface on router R2 and is distributed to OSPF area 0, but the ping fails from router R3.
Which of the following is a possible solution to the problem?
What are some of the characteristics of Alcatel-Lucent's implementation of non-stop routing? (Choose two)
There is an IP host with IP address 10.2.3.1. A static route is created, using the "configure router static-route 10.2.3.0/24 next-hop 10.1.2.1" command. What is the correct traceroute command to test this static route on an Alcatel-Lucent 7750 SR?
Click the exhibit button.
The OSPF adjacency between routers R3 and R1 is down. What is the problem?