E20-375 Sample Questions Answers

A customer is evaluating the deployment of RecoverPoint with their VMAX array. They want to deploy the RPAs in the virtual appliance form. They ask your opinion about using vRPA versus physical appliances.

What should you advise them?

When modifying a cluster's settings, what value can be changed from the Environment Settings screen in Deployment Manager?

Which virtualization solution components are supported by RecoverPoint?

A large data center is hosting storage protection solutions for multiple companies. This solution is accomplished by the hosting organization's ability to consolidate data to an environment with two VNX arrays.

How many RecoverPoint clusters can be used in this environment?

A new RecoverPoint/SE environment has been installed with a single cluster. There are no limitations regarding journal sizes and you want to choose how frequently RecoverPoint can create point-in-time copies.

What is the highest frequency available for point-in-time copies in this environment?

Through what does RecoverPoint support heterogeneous storage environments?

A customer has three VMAX arrays and one VNX array fronted by an EMC VPLEX. They want to use RecoverPoint to protect their environment.

How many licenses, of which type, would be required for their environment?

A company recently acquired a new DR site and requires their production data to be replicated to this DR site.

What is an important consideration about the RecoverPoint out-of-band architecture?

Which RecoverPoint features are supported on physical and virtual RPAs?

What is the maximum number of copies supported using the MetroPoint topology for VPLEX continuous data replication?

An administrator experiences a serious error with an RPA and calls EMC Support to resolve the issue. They are concerned that the system did not automatically notify EMC Support via the ESRS gateway. You check all settings in Unisphere Configure System Notification and find they are correct.

What is the most likely cause for this notification failure?

Which RecoverPoint tool will give you an overview of the system state, based on the system’s long term statistics?

A customer has a four-node RecoverPoint cluster using a VNX array. All LUNs are replicating and failover has been tested. The customer would like to integrate RecoverPoint and Unisphere. However, they are unable to manage the cluster through Unisphere.

What should the customer do to correct the issue?

What is the maximum number of copies of production data supported with RecoverPoint?

A company has a RecoverPoint environment with 20 Consistency Groups doing remote replication. A new building was just acquired for disaster recovery and they want to move to this new location. The IP addresses and cluster name are going to be changed.

What should the company consider before making the proposed change?

A customer has a four-node RecoverPoint cluster replicating over a 10 Mbps WAN link. They have a requirement to upgrade the WAN link to 1 Gbps. This will require a change of the default gateway on the RPAs. They need to accomplish this with as little impact as possible.

What can be done?

Which RecoverPoint tool is used for system conversions?

When adding a new vRPA, what is the only storage authentication method that is supported?

An existing RecoverPoint/CL environment consists of one cluster at the main office and two off-site DR clusters. You have been asked to expand the environment to the maximum number of DR sites using RecoverPoint.

How many additional clusters could be added to this RecoverPoint Environment?

When using Deployment Manager to install RecoverPoint/SE, which zoning methods are available with Brocade switches?

A customer environment includes a two-cluster RecoverPoint/SE instance. They have a new data center 100 km away that they wish to protect with RecoverPoint.

What steps are required to connect a new cluster to their existing RecoverPoint instance?

What are the three potential bottlenecks that can cause a RecoverPoint Consistency Group to go into High Load?

A company recently acquired a new DR site and requires local Fibre Channel based production data to be replicated synchronously. They are investigating what infrastructure is needed on this DR site.

What is an important connectivity consideration?

The Getting Started wizard that is displayed the first time a user accesses Unisphere for RecoverPoint assists with performing what action?

When RecoverPoint is deployed with a VMAX splitter, what presents the virtual target and virtual remote devices?

A Consistency Group consists of one production copy, one local copy, and two remote copies.

How many journals are required for this configuration?

In order to create a new Consistency Group, a user should navigate to which option within the Protection tab of Unisphere for RecoverPoint?